Swamp cooler hook up

swamp cooler hook up

How do I hook up my swamp cooler?

Swamp coolers installed on the ground or side-mounted in a window are the simplest to hook up. You can easily supply water to these units by running a supply line from the cooler to a spigot on the outside of your home. A simple adapter allows you to attach the water supply line directly onto the hose bib for a fast and easy hookup.

Do swamp coolers need a water supply line?

They do need a constant supply of water to operate, however, so youll have to hook yours up to a water supply line before summer weather hits. Swamp coolers installed on the ground or side-mounted in a window are the simplest to hook up.

How do you stop a swamp cooler from leaking water?

Install a shutoff valve on the water supply line leading to your swamp cooler in case you develop a leak at some point in the future. Note that you can do this job more quickly if you use a saddle valve to connect the swamp cooler water supply line to your water heater supply line.

Can you put a swamp cooler in the attic?

The best time to rough in your swamp cooler wiring and water line for your new cooler is after the holes are cut through the roof and ceiling, but before the ductwork is installed. The attic will be relatively cool because of the natural ventilation of the heat exiting the roof.

How do you hook up a swamp cooler to a water heater?

Run the irrigation line through the attic and down through an interior wall or flue to the water heater. Your water line will follow the same path as the swamp coolers electrical wiring most of the way. Verify that the water line isnt touching the sides of the flue.

Do swamp coolers need a water supply line?

They do need a constant supply of water to operate, however, so youll have to hook yours up to a water supply line before summer weather hits. Swamp coolers installed on the ground or side-mounted in a window are the simplest to hook up.

How do you fix a swamp cooler that wont turn on?

Slide the plastic sleeve and brass nut down onto the threads of the swamp cooler and tighten the nut by hand. When the nut is hand-tight, use a wrench to tighten it another 1/4 turn. Run your irrigation line from the swamp cooler down to the ground if necessary and then run it along your home to the water supply.

How do you install a pump sleeve on a swamp cooler?

If the sleeve has a flange on one side, be sure to install the sleeve so that the flange faces out. Slip the end of the irrigation tubing into the float hookup on the swamp cooler. Slide the plastic sleeve and brass nut down onto the threads of the swamp cooler and tighten the nut by hand.

Do swamp coolers need to let air out?

For swamp coolers to work, you need to let air out at the same rate that the swamp cooler is blowing air in. That way, humidity wont build up in your house, making it seem warmer than it actually is. Though opening windows seems counter-intuitive, it actually helps your swamp cooler work better.

How do I adjust the temperature in my house with a swamp cooler?

You can adjust the temperature in your house by installing an electronic swamp cooler thermostat. How does a swamp cooler work? A traditional swamp cooler control requires you to manually turn the cooler on and off, set the pump to soak the pads, and adjust the fan speed.

How much space do you need for a swamp cooler window?

Though opening windows seems counter-intuitive, it actually helps your swamp cooler work better. Youll need 1 to 2 square feet (0.093 to 0.186 m 2) of open window space per 1,000 cfm, which is the units cooling capacity. You dont want to open them too far because that lets in hot air.

What is the best way to cool an attic?

A portable air conditioner is the easiest solution for cooling your attic. It’s a standalone unit that’s about two feet tall and 18 inches wide and has wheels for mobility. Portable air conditioners do need to be vented to pump the hot air outside. Most come with a window kit for this purpose that attaches to a hose on the back of the unit.

Related posts: