Propane pool heater hookup

propane pool heater hookup

Can I install a propane gas pool heater?

If you live in an area without natural gas service but want the comfort and convenience of a gas pool heater, you can install a propane gas pool heater! Just about any natural gas heater you can buy is also available as a propane heater. The only difference is in the orifice sizes, for the gas valve and burner orifices.

How do you hook up a pool heater?

Few heaters will be bolted to the ground and will simply connect to your pools plumbing lines and propane tank. The heaters are quite heavy and this is what will keep the heater in the right position.

How does a propane pool heater work?

The pump forces water from the intake into the unit where the propane gas heats up the water. Warm water will now exit through the pool jets. The heater starts up each time the temperature goes below the desired setting. The heater will only turn on when the temperature is below its designated level.

How do you connect a propane tank to a water heater?

Ensure the designated location is close to the propane tank. Position the heater on the slab, and move it so the plumbing and gas lines are easy to access. Connect the heater to the water line. Use a hacksaw to cut through the PVC pipe in order to fit a PVC elbow joint on the water line.

How do you connect a propane tank to a pool heater?

Propane Gas Connection This is the easy part. Just call up your local propane providers, and tell them you want a quote to install propane tanks and make a connection to your new propane pool heater. They’ll ask you what size of heater it is – they need to know the output in BTU’s.

How much propane does it take to run a pool heater?

A typical size 200,000 BTU heater can use up to 2 gallons an hour of propane. This means using your propane gas pool heater will cost anywhere between $8 to $12 per hour to operate. To heat a 10,000-gallon swimming pool, without using a solar cover, will usually take about 8 to 16 hours.

Can you put a propane pool heater on a concrete slab?

The propane pool heater should be placed on a level concrete slab so that the heater is stable. If you have gas available then you might consider using a gas heating system rather than propane as it will be cheaper. The heater will normally need to be located close to the propane tank.

How do I replace my gas pool heater?

Once you have purchased the correct size and type of pool heater (propane or natural), the first step in replacing your gas pool heater is to remove your current heater and clear the location where the new pool heater will be installed.

How do you connect a propane tank to a gas heater?

Run threaded iron pipe from the outdoor propane tank to the heater; tighten all connections with a pipe wrench. 5. Use a union fitting to connect the threaded gas pipe to the heater. 6. Run copper pipe from the existing water-supply line to the heater.

How far should a propane tank be from a water heater?

The propane tank needs to be at least 10 feet from the water heater. Some municipalities might require a greater distance, so check local regulations in case you need more than 10 feet. The propane tank should not be under an awning or other shelter that could retain vented gas from the propane tank.

How do you fix a leaking propane tank on a water heater?

Open the propane tank valve, usually a round handle on the top of the tank, and the shutoff valve to the water heater to pressurize the line. Put 2 teaspoons of dish soap in a cup of water, mix it gently and swab the solution onto all your unions to check for leaks.

How to install a tankless water heater?

Cut into the existing water–supply pipes attached to the old water heater. 3. Remove the old water heater and mount the new tankless heater to the wall. 4. Run threaded iron pipe from the outdoor propane tank to the heater; tighten all connections with a pipe wrench. 5. Use a union fitting to connect the threaded gas pipe to the heater. 6.

Related posts: